- 您现在的位置：买卖IC网 > Sheet目录883 > SRBA-06F2A0G (Bel Fuse Inc)CONV DC/DC .75-3.63VDC 6A OUTPUT
NON-ISOLATED DC/DC CONVERTERS
2.4 Vdc - 5.5 Vdc Input
General Specifications
0.75 Vdc - 3.63 Vdc/6 A Output
Parameter
Min
Typ
Max
Notes
Efficiency
Vo=3.3 V
Vo=2.5 V
-
-
93%
91%
-
-
Vo=1.8 V
Vo=1.5 V
Vo=1.2 V
Vo=0.75 V
Switching Frequency
Over Temperature Shutdown
Output Voltage Trim Range
MTBF
-
-
-
-
250 kHz
-
0.7525 V
88%
87%
84%
78%
300 kHz
135 ° C
-
6,976,379 hours
-
-
-
-
350 kHz
-
3.63 V
Measured at Vin=5 V, full load
Calculated Per Bell Core SR-332 (Vin=5 V;
Vo=0.75 V, I O = 4.8 A; T a = 25 ° C)
Dimensions
Inches (L × W × H)
Millimeters (L × W × H)
0.8 x 0.45 x 0.25
20.32 x 11.42 x 6.36
Weight
-
5g
-
Note : All specifications are typical at 25 ° C unless otherwise stated.
Control Specifications
Parameter
Min
Typ
Max
Notes
Remote On/Off
Signal Low (Unit Off)
Signal High (Unit On)
Signal Low (Unit On)
Signal High (Unit Off)
Sequencing Voltage
Sequencing Slew Rate Capability
Sequencing Delay Time
-0.2 V
-
-0.2 V
1.5 V
0V
-
10 mS
-
-
-
-
-
-
-
0.3 V
Vin, max
0.3 V
Vin, max
Vin
2 V/ mS
-
Active High: SRBA-06F2A0; Remote On/Off
pin open, Unit on.
Active Low: SRBA-06F2AL; Remote On/Off
pin open, Unit on.
Sequencing Voltage applied on SEQ pin
should be higher than output voltage.
Delay from Vinmin to application of voltage on
SEQ pin
Tracking Accuracy
Power-Up
Power-Down
-
-
100 mV
200 mV
200 mV
400 mV
Output Trim Equations
Equation for calculating the trim resistor (in k ? ) given the desired adjusted voltage (Vadj) is shown below. The
Trim Up resistor should be connected between the Trim pin and Ground.
Vout
R TrimUp =
21 . 07
V adj ? 0 . 7525
? 5 . 11
Module Trim
GND
Rtrim
Equation for calculating the trim voltage (in V) given the desired adjusted voltage (Vadj) is shown below. The
Trim Up voltage should be connected between the Trim pin and Ground.
Vout
V TrimUp = 0 . 7 ? 0 . 1698 × ( V adj ? 0 . 7525 )
Module
Trim
Vtrim
GND
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 ? Tel 201-432-0463 ? Fax 201-432-9542 ? www.belfuse.com
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
SRBC-10A2A0G
CONV DC/DC .75-5V ADJ 10A SMD
SRBC-10E2A0G
CONV DC/DC .75-3.63 VDC 10A OUT
SRBC-10F2A0G
CONV DC/DC .75-3.63 VDC 10A OUT
SRBC-16A2A0G
CONV DC/DC .75-5V ADJ 16A SMD
SRBC-16E2A0G
CONV DC/DC .75-3.63 VDC 16A OUT
SRBC-16F2A0G
CONV DC/DC .75-3.63 VDC 16A OUT
SRE6603-102M
INDUCTOR SHIELDED PWR 1000UH 20%
SRF0703-220M
IND SHIELDED POWER 22UH SMD
相关代理商/技术参数
SRBA-06F2AL
制造商:Bel Fuse 功能描述:DC/DC PS SGL-OUT 0.75V TO 3.63V 6A 21.8W 6SMD - Trays 制造商:Bel Fuse 功能描述:Module DC-DC 1-OUT 0.75V to 3.63V 6A 21.8W 6-Pin SMD
SRBA-06F2ALG
功能描述:CONV DC/DC .75-3.63VDC 6A OUTPUT RoHS:是 类别:电源 - 板载 >> DC DC Converters 系列:SRBA 标准包装:33 系列:Econoline R1D 类型:隔离 输出数:2 电压 - 输入（最小）:21.6V 电压 - 输入（最大）:26.4V Voltage - Output 1:15V Voltage - Output 2:-15V Voltage - Output 3:- 电流 - 输出（最大）:33mA，33mA 电源（瓦） - 制造商系列:1W 电压 - 隔离:3kV（3000V） 特点:- 安装类型:表面贴装 封装/外壳:12-DIP SMD 模块（10 引线） 尺寸/尺寸:0.60" L x 0.42" W x 0.28" H（15.2mm x 10.7mm x 7.0mm） 包装:管件 工作温度:-40°C ~ 100°C 效率:82% 电源（瓦特）- 最大:1W 其它名称:10900377
SRBA-06F2AX
制造商:BEL 制造商全称:Bel Fuse Inc. 功能描述:NON-ISOLATED DC/DC CONVERTERS
SRBA-06F2AX_07
制造商:BEL 制造商全称:Bel Fuse Inc. 功能描述:NON-ISOLATED DC/DC CONVERTERS
SR-BB
制造商:C&K Components 功能描述:
SRBBRCT-KIT
功能描述:电缆固定件和配件 Strain Relief Bar Kit with Cable Ties/Sl RoHS:否 制造商:Heyco 类型:Cable Grips, Liquid Tight 材料:Nylon 颜色:Black 安装方法:Cable 最大光束直径:11.4 mm 抗拉强度:
SRBBRKT
功能描述:电缆固定件和配件 Strain Relief Bar Bracket RoHS:否 制造商:Heyco 类型:Cable Grips, Liquid Tight 材料:Nylon 颜色:Black 安装方法:Cable 最大光束直径:11.4 mm 抗拉强度:
SRBBRM-KIT
功能描述:电缆固定件和配件 Strain Relief Bar Kit with Hook and Loop RoHS:否 制造商:Heyco 类型:Cable Grips, Liquid Tight 材料:Nylon 颜色:Black 安装方法:Cable 最大光束直径:11.4 mm 抗拉强度: